ESP32-CAM WiFi Bluetooth Development Board with ESP32S and OV2640 Camera Module

Description The ESP32CAM is a tiny module based on ESP32S module which comes with OV2640 Camera module. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core. The ESP32CAM equips the ESP32 with everything necessary to program, run and develop on the wonderchip. Additionally, the board reserved the MPU6050,BME280 and an analog MIC. ESP integrates WiFi, traditional bluetooth and BLE Beacon, with 2 high-performance 32-bit LX6 CPUs, 7-stage pipeline architecture, main frequency adjustment range 80MHz to 240MHz, on-chip sensor, Hall sensor, temperature sensor, etc. Fully compliant with WiFi 802.11b/g/n/e/i and bluetooth 4.2 standards, it can be used as a master mode to build an independent network controller, or as a slave to other host MCUs to add networking capabilities to existing devices. ESP32-CAM can be widely used in various IoT applications. It is suitable for home smart devices, industrial wireless control, wireless monitoring, QR wireless identification, wireless positioning system signals and other IoT applications. It is an ideal solution for IoT applications. Features Ultra-small 802.11b/g/n Wi-Fi BT/BLE SoC module Low-power dual-core 32-bit CPU for application processors Up to 240MHz, up to 600 DMIPS Built-in 520 KB SRAM, external 4M PSRAM Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC Support OV2640 and OV7670 cameras with built-in flash Support for images WiFI upload Support TF card Support multiple sleep modes Embedded Lwip and FreeRTOS Support STA/AP/STA AP working mode Support Smart Config/AirKiss One-click distribution network Support for serial local upgrade and remote firmware upgrade (FOTA) Support secondary development Technical Specification Module model ESP32-CAM Package DIP-16 Size 27*40.5*4.5(±0.2)mm SPI Flash default 32Mbit RAM internal520KB external 4M PSRAM Bluetooth bluetooth4.2BR/EDR and BLE standards Wi-Fi 802.11 b/g/n/e/i Support interface UART, SPI, I2C, PWM Support TF card Maximum support 4G IO port 9 Serial port rate default 115200 bps Image output format JPEG (only supported by OV2640), BMP, GRAYSCALE Spectrum range 2412 ~ 2484MHz Antenna form onboard PCB antenna, gain 2dBi Transmit power 802.11b: 17±2 dBm (@11Mbps) 802.11g: 14±2 dBm (@54Mbps) 802.11n: 13±2 dBm (@MCS7) Receiving sensitivity CCK, 1 Mbps : -90dBm CCK, 11 Mbps: -85dBm 6 Mbps (1/2 BPSK): -88dBm 54 Mbps (3/4 64-QAM): -70dBm MCS7 (65 Mbps, 72.2 Mbps): -67dBm Power consumption Turn off the flash: 180mA@5V Turn on the flash and adjust the brightness to the maximum: 310mA@5V Deep-sleep: The lowest power consumption can reach 6mA@5V Modern-sleep: up to 20mA@5V Light-sleep: up to 6.7mA@5V Security WPA/WPA2/WPA2-Enterprise/WPS Power supply range 5V Operating temperature -20 °C ~ 85 °C Storage environment -40 °C ~ 90 °C, < 90%RH [!] Notes: Please ensure that the module input power is at least 5V 2A, otherwise the image will unstable. ESP32 GPIO32 pin controls camera power. When the camera is working, please pull GPIO32 low. Since IO0 is connected to the camera XCLK, please leave IO0 floating when using it. Do not connect high and low level. The factory has the default firmware, no additional download is available. Please handle it carefully if you need to re-burn other firmware. Documents and Downloads ESP32 Camera Module Schematic and Pinout page A tutorial on ESP32-CAM and Arduino IDE ESP32 Technical Reference manual ESP32 RTOS SDK on Github Package Includes 1x ESP32-CAM WiFi Bluetooth Development Board 1x OV2640 Camera Module ESP32-CAM WiFi Bluetooth Development Board with ESP32S and OV2640 Camera Module in Rawalpindi Islamabad Pakistan. DIY Security Camera, DIY QR Scanner. ESP32-CAM Tutorial